TS-PGM36-555-1280 Planetary DC Geared Motor 12V 24V

Feature:

Model:

其他信息

Factory

Faradyi

Model

TS-PGM36-555-1280

Voltage

DC 12/24V

Current

300/400 MA

Rotaed Speed

9-1240 RPM

Thanks for sharing it !

Category

Proudct Information:

Description

Item Description: TS-PGM36-555-1280 Planetary DC Geared Motor 12V 24V

(1) About Planetary Geared Motor:
– A versatile motor with small size, low noise, substantial output torque, stable operation, and an extended lifespan. The planetary gear motor’s life is three times that of an ordinary gear motor, provided the project load stays within the motor’s torque capacity.

(2) Rated Voltage:

– DC 12V or DC 24V

(3) No Load Speed Options:
– 36 / 50 / 71 / 100 / 185 / 357 / 962 RPM

(4) Rated Load Torque:
– The motor’s torque varies with its speed. Slower speeds provide greater torque, and faster speeds support lighter loads. Torque decreases as speed is reduced, and the final torque may vary based on the chosen speed.

> Note: Contact us to understand torque changes with speed and make an informed purchase.

(5) Rotation Direction:
– Clockwise (CW) or Counterclockwise (CCW); Supports Reversal

(6) Gear Material:
– Metal gears for extended motor life

(7) Speed Adjustment:
– Motor speed can be adjusted using a speed controller. Contact us for suitable controllers. Note that as speed decreases with a controller, motor torque also decreases, and attention is needed to avoid damage.

(8) Versatile Applications:
– Suitable for various micro-automation equipment, including Smart Robots, Smart Door Locks, DIY tanks, etc. Confirm voltage and torque suitability for your project before purchase.

Feel free to contact us for assistance in selecting the right motor and avoiding potential issues. Thank you for considering our products!

TS-PGM36-555-1280 Planetary DC Geared Motor 12V 24V TS-PGM36-555-1280 Planetary DC Geared Motor 12V 24V TS-PGM36-555-1280 Planetary DC Geared Motor 12V 24V TS-PGM36-555-1280 Planetary DC Geared Motor 12V 24V TS-PGM36-555-1280 Planetary DC Geared Motor 12V 24V TS-PGM36-555-1280 Planetary DC Geared Motor 12V 24V

 

Instructions For Use

1. Welding power cord:
The soldering iron temperature is 340°C + 40 °C, and the welding time is controlled within 3 seconds. The plastic of the motor terminal cannot be deformed, and at the same time, coal and tin cannot flow into or drip into the motor, otherwise the motor cannot be used or the service life will be affected.

2. Motor installation:
Pay attention to the length of the screw for the installation of the optical motor. If it is too long, it will contact the motor rotor, When the motor is damaged, the force of tightening the screw should not be too large. If there is a bracket need to consult customer service to buy.

3. Beware of eccentric load:
When the motor drives an eccentric load, pay attention to the load should not be too large, otherwise it will seriously affect the life of the motor.

4. Do not overload work:
When the motor is overloaded, the working current will be very large, resulting in serious heating of the motor. In order to ensure the service life of the motor, please check whether the load is used in accordance with the regulations and cannot be overloaded.

5. Beware of stalling:
During the use of the light motor, it should not be blocked for a long time (stuck without turning), otherwise the motor will overheat, burn the coil, and even cause a fire. For the use of the reduction motor, please consult customer service before use whether this parameter can be blocked instantly. If it is blocked during use, the reduction gearbox may be damaged.

6. Installation of shaft end fittings:
When the shaft end of the motor is pressed into parts such as pulleys or gears (tight fitting), please consult customer service. Non-standard operation may damage the motor.

7. Operating environment:
Temperature -20°C ~ 60°C, humidity 30% ~ 90% RH. Other circumstances please consult customer service.

8. Storage attention:
Do not place in high temperature and humid environment, and do not place in corrosive gas.

Faradyi Motors Service

How to use the motor

1. Use tolerance: pay attention to the use range of voltage and current, and use the motor under the conditions specified in this standard, otherwise the life of the motor will be reduced.
2. Handling the motor: handle it with care, and use the motor casing as much as possible.
3. Motor wiring: the red lead wire is connected to the positive pole, and the black lead wire is connected to the negative pole. If the connection is reversed, the motor will rotate in the opposite direction.
4. Overload: Use it within the specified load range as much as possible. It is strictly forbidden to run the motor in a stalled state or close to the stalled state for a long time, otherwise the motor will burn out.
5. Motor storage:Storage temperature: 0C-40°C, storage humidity: 15%-90% RH
Avoid placing it in an environment with high temperature, high humidity and corrosive gas.
6. Motor operating temperature: 0°C-70C

Motor Precautions

1. When you use the motor, there must be no binding objects, such as adhesive, do not flow into the bearing through the rotating shaft, which will hinder the operation of the motor.
2. The rotation of the shaft may have the opposite effect on the life of the motor. In order to prolong the life, please check whether your load is in accordance with the regulations. Do not overload or hang items that hinder the rotation of the shaft.
3. Manufactured into an eccentric heavy radiation load, harmful to the life of the motor.
4. Do not store it in high temperature or extreme humidity, and do not place it in corrosive gas, which will reduce the effect of the motor
5. Do not run the motor in the surrounding high temperature and humidity.
6. When soldering on the positive and negative motor terminals of the power supply, the temperature of the soldering iron is 340C40C, and the heating time is within 3 seconds. Do not deform the plastic. Let the solder point flow into the motor or break the end of the wire during work, which will make the motor function decline.
7. Do not let the motor shaft get stuck. When the power is supplied, the motor will overheat in a short time and burn its accessories.
8. Supply the specified power and make sure it is within the range of measurable requirements.
9. When installing pulleys or gears, do not increase the weight abnormally when pressing them in.
10. When installing the motor, if the screw is too long, it will cause contact between the motor itself and the
rotor, which will affect the characteristics.

Related Products

Submit a Quick Quote

Don't Take Our Word for It - See What Customers Say

We strive to provide exceptional products and service. If you are satisfied with your experience, we would greatly appreciate you taking a moment to leave us a review

en_USEnglish

Product Inquiry

Product Inquiry